Search results for: 'angle seat valve'

• 10 bar Gas / 16 bar Water
• Branch Saddle installation only with installation set Topload TL225 (799.300.807)
• Angle adaptors (799.350.340) for fusion cable required
• 4 mm pin connectors
• Limited path fusion indicators
• Spigot outlet for butt- and electrofusion
• Full pressure applicable - no derating factor
• With integrated pressure test port for test cap (799.199.287)

• 10 bar Gas / 16 bar Water
• With integrated drill bit to tap live mains under pressure
• Complete with lower part and premounted PE100 coated valve piece
• The valveis closed clockwise
• Number of turns to fully open or close valve is 13 for outlet d32
• Number of turns to fully open or close valve is 28 for outlet d63
• Spindle size (SW) 14
• 4 mm pin connectors
• Limited path fusion indicators
• Long fusion outlet

• Built on with pneumatic actuator PA11 (DN10/15-25), PA21 (DN32-50)
• Control time 90°<) 1-2s
• For easy installation and removal
• Integrated stainless steel mounting inserts

• For IR, butt and electrofusion welding according to DVS 2207
• Type A: without chamfer
• Type B: with chamfer
• Suitable for plastic butterfly valves type 567/578/565 up to DN250. ecoFit adapter SDR11 required for DN350 and above
• Suitable for metal butterfly valves type 038/039/044/065 up to DN250. ecoFit adapter SDR11 is required for DN350 and above
• Profile seal: d20-d800 NBR, EPDM, FKM
• Flat gasket: d20-d315 EPDM, FKM
• Pressure rating: 16 bar water / 10 bar gas
• Please refer to the Online Tool: Perfect Flange Connection - GF Piping Systems (gfps.com)

• For IR, butt and electrofusion welding according to DVS 2207
• Type A: without chamfer
• Type B: with chamfer
• Suitable for plastic butterfly valves type 567/578/565 up to DN250. ecoFit adapter SDR11 required for DN350 and above
• Suitable for metal butterfly valves type 038/039/044/065 up to DN250. ecoFit adapter SDR11 is required for DN350 and above
• Profile seal: d20-d800 NBR, EPDM, FKM
• Flat gasket: d20-d315 EPDM, FKM
• Pressure rating: 16 bar water / 10 bar gas
• Please refer to the Online Tool: Perfect Flange Connection - GF Piping Systems (gfps.com)

• For IR, butt and electrofusion welding according to DVS 2207
• Type A: without chamfer
• Type B: with chamfer
• Suitable for plastic butterfly valves type 567/578/565 up to DN250. ecoFit adapter SDR11 required for DN350 and above
• Suitable for metal butterfly valves type 038/039/044/065 up to DN250. ecoFit adapter SDR11 is required for DN350 and above
• Profile seal: d20-d800 NBR, EPDM, FKM
• Flat gasket: d20-d315 EPDM, FKM
• Pressure rating: 16 bar water / 10 bar gas
• Please refer to the Online Tool: Perfect Flange Connection - GF Piping Systems (gfps.com)

• For IR, butt and electrofusion welding according to DVS 2207
• Type A: without chamfer
• Type B: with chamfer
• Suitable for plastic butterfly valves type 567/578/565 up to DN250. ecoFit adapter SDR11 required for DN350 and above
• Suitable for metal butterfly valves type 038/039/044/065 up to DN250. ecoFit adapter SDR11 is required for DN350 and above
• Profile seal: d20-d800 NBR, EPDM, FKM
• Flat gasket: d20-d315 EPDM, FKM
• Pressure rating: 16 bar water / 10 bar gas
• Please refer to the Online Tool: Perfect Flange Connection - GF Piping Systems (gfps.com)
• FM 1613 approved - PN 15

• Cutting edge technology for maximum productivity.
• Tooth design - A 3.5 teeth per inch tooth design with a positive 10‚° tooth angle provides the following benefits: - Faster and more aggressive cut. - Improved heat dispersion during cutting ensures that the teeth stay sharper for longer. - Deeper curved gullets provide more efficient chip clearance preventing clogging and heat build up. - Special shaped tooth angle has less tendency to snag on thinner materials. - Teeth are altenate side set to minimise binding and friction. - Requires less feed pressure - This is achieved by the combination of aggressive tooth geometry and good chip clearance resulting in the requirement of less force during drilling.
• Tooth material - Type Matrix II premium high speed steel is used for the toothed area of the holesaw. Matrix II steel contains 8% cobalt allowing the teeth to retain the original tooth hardness even at high working temperatures when used in metal cutting applications. - Bi-Metal construction - High speed steel teeth are laser weldedonto a high alloy steel body. The teeth are then vacuum hardened to 65 HRC at a temperature of 600‚°C to give maximum durability and life time. - Due to the high wear resistance of the Matrix II material, these holesawsare ideal for cutting difficult and hard materials such as stainless steel and acid resistant steels as well as softer materials like wood.
• Holesaw body - 1.27 mm thick steel holesaw body is rigid to retain itsshape but also has built in elasticity. - Effective sawing depth is 41 mm.
• Back plate design - The back plates are constructed with thick steel thus the holes will not enlarge over time. Thick backs add strengthand rigidity minimising vibrations. - 4 drive pin holes for easier arbor location. - Perfectly manufactured round back plate, especially important for the larger diameter holesaws.
• Diagonal slots aid the removaland ejection of the core.
• Applications - High quality manufacturing techniques ensure high rotational precision, therefore these holesaws are suitable for use both in hand and pillar drills (manual feed only).L49224152

connector set 3/8"

for copper pipe 10 mm

TDL handles

marking: neutral

escutcheon

GROHE StarLight finish

• Consisting of:
• hand shower with trigger control (26 328)
• valve with integrated shower holder (26 333 000)
• Silverflex Longlife shower hose 1250 mm (26 335)
• GROHE StarLight chrome finish
• SpeedClean anti-limescale system
• Twistfree preventing the hose from twisting
• Min. recommended pressure 0.5 bar
• Please refer to local norms regarding installation.

• normal spray
• ƒ 400 mm
• material: metal
• ball joint with turning angle 20‚°‚± 20‚°
• connection thread 1/2"
• GROHE DreamSpray perfect flow
• GROHE StarLight chrome finish
• SpeedClean anti-lime system
• this head shower should only be used in conjunction with shower arm 26 146, 28 982 or 28 497

• pre-assembled headpart 3/4"
• short spindle
• protection sleeve
• thread union 3/4"
• DR-brass